MICRO2
White/Black
Microperforated Films
gloss 1000 mm 10, 30, 90, 120 m medium term polymeric PVC
This film is composed of 165-µm, micro-perforated, colaminated (black/white), polymeric PVC, which is coated with a pressure-sensitive acrylic adhesive. For solvent, eco-solvent and latex inkjet printing.
Samenstelling & formaat
| Filmtype | polymeric PVC |
| Dikte | 165 µm |
| Kleeflaag | clear |
| Liner | Liner kraft |
| Breedte (mm) | 1000,1370,1520 |
| Lengte (m) | 10, 30, 90, 120 |
Verwerking
| Toepassing | window graphics |
| Ondergronden | windows |
| Oppervlakken | slightly curved |
| Aanbrengmethode | Dry application method |
| Minimale aanbrengtemperatuur | +10 °C (+50 °F) |
| Gebruiksbereik | -10 °C to +50 °C (+14 °F to +122 °F) |
| Duurzaamheid | medium term |
Technische eigenschappen
| Tack | 10 N/25 mm |
| Hechting (20 min) | 8 N/25 mm |
| Hechting (24 h) | 13 N/25 mm |
| Afpelkracht liner | 0.4 N/25 mm |
| Treksterkte | min. 25 N/25 mm |
| Rek bij breuk | min. 40 % |
| Krimp (168 h / 70 °C) | < 0.4 mm |
| Brandgedrag | EN 13501-1 |
Toepassing & onderhoud
- Apply to untreated, clean and dry mineral glass. Not to be immersed in water.
- Prior to application, clean the substrate with solvent- and ammonia-free detergents only.
- Leave a 5-mm space between the window sealings and the edge of the MICRO2 film. Never apply the film directly to the window sealings.
- It is possible to peel the film off the substrate. Remove residual adhesive if necessary.
Caution: This micro-perforated film cannot be used on emergency exits of public passenger transport vehicles (Appendix 5 of the Geneva Regulation R43 or 92/22/CEE directive). The customer is strongly advised to contact the competent local authorities who will validate the conformity of the vehicle with the road traffic regulations in effect.
Aanbevelingen
- Optimal drying time for the inks before laminating or further processing is 24 hours minimum.
On flat substrates, it is recommended to laminate with an adhesive-coated, super-transparent, cold laminating film (PG836), applied using a laminator.
DO NOT USE heat-sealing (heat encapsulating) film.
- For vehicle rear windows (slightly curved), we recommend using our "cast" cold laminate PC50MICP2.
- The MICRO2 film's adhesion at edges and corners can be reinforced with our self-adhesive edge sealing tapes "FPG836" for flat surfaces, "FPC50MICP2" for slighty curved substrates or our sealing varnish VR7077 in case of extreme mechanical stress.
The sealing must be done by applying the tape or varnish on the MICRO2 film and the glass substrate while avoiding any contact with the seals.
- For more information on the application method of the MICRO2 film, please refer to its Application Guide available under the "Professionals" heading, in the "Digital printing media” category on our website www.hexis-graphics.com.
Duurzaamheid in detail
- Vertical outdoor exposure:
- Blank: 4 years
- Printed and laminated: 3 years
- Removability: up to 6 months after application without leaving significant adhesive residues.
